Laboratory and Field Tests of Hardness and Wear Resistance of Heat-Treated Steel Samples and Machine Parts
Abstract
This article describes the method of testing the hardness and wear resistance of hardened and released steel samples and machine parts in laboratory and field conditions. Samples with wear-resistant carbide coating obtained by casting according to expanded polystyrene gasified models are presented. The compositions, properties and abrasive wear resistance of cast steel samples before and after heat treatment with double phase recrystallization were studied. It is shown that heat treatment with double phase recrystallization increases the hardness and wear resistance of cast samples and parts by 2-3 times higher than serial ones.
References
2. Мухамедов А.А., Бердиев Д.М. Повышение износостойкости деталей почвообрабатывающих машин термообработкой // Композиционные материалы. – Ташкент, 2006. №2. - С.23-27.
3. Тилабов Б.К. Износостойкость наплавочного твердого сплава типа ПГ-С27 с метастабильным аустенитом и мартенситом // Республиканский межвузовский сборник научных трудов. – Ташкент, 2011. Вып.1. - С.359-364.
4. Махкамов К.Х. Ударно-абразивный износ деталей машин. – Т.: ТашГТУ, 2013. - 223 с.
5. Гутерман В.М., Гамольская З.М. Износостойкость сталей в условиях гидроабразивного износа. – М.: Машгиз, 2006. - 187 с.
6. Тилабов Б.К. Основы теории и технологии нового перспективного процесса получения литых деталей машин с износостойким твердосплавным покрытием путем литья по газифицируемым моделям. Монография. – Ташкент.: «Фан ва технология», 2017. - 160 с.
7. Бернштейн Д.Б. Абразивное изнашивание лемешного лезвия и работоспособность плуга // Тракторы и сельскохозяйственные машины. – М.: ТСМ, 2002. №6. - С.39-43.
8. Меськин В.С. Основы легирования стали. – М.: Металлургиздат, 1987. - 316 с.
9. Гудремон Э.Г. Специальные стали. Т.1,2. – М.: Металлургиздат, 1989. - 237 с.
10. Тилабов Б.К. Создание оптимального химического состава и улучшение механического свойства литых рабочих колес и цильпебсов, изготовленных из высокохромистого белого чугуна // Композиционные материалы. – Ташкент, 2019. №3. - С.4-8.
11. Tilabov B.K. Increased durability of iron parts by thermal treatment with double phase recrystallization. European applied sciences. 2015. Europaische Fachhochschule. ORT Publishing. Germania, 2015. - C.49-53.
12. Тилабов Б.К. Твердость и микротвердость твердосплавных покрытий до и после термической обработки // Горный Вестник Узбекистана. – Навои.: НГГИ, 2020. №1. - С.49-53.
In submitting the manuscript to the International Journal on Integrated Education (IJIE), the authors certify that:
- They are authorized by their co-authors to enter into these arrangements.
- The work described has not been formally published before, except in the form of an abstract or as part of a published lecture, review, thesis, or overlay journal.
- That it is not under consideration for publication elsewhere,
- The publication has been approved by the author(s) and by responsible authorities – tacitly or explicitly – of the institutes where the work has been carried out.
- They secure the right to reproduce any material that has already been published or copyrighted elsewhere.
- They agree to the following license and copyright agreement.
License and Copyright Agreement
Authors who publish with International Journal on Integrated Education (IJIE) agree to the following terms:
- Authors retain copyright and grant the International Journal on Integrated Education (IJIE) right of first publication with the work simultaneously licensed under Creative Commons Attribution License (CC BY 4.0) that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors can enter into separate, additional contractual arrangements for the non-exclusive distribution of the International Journal on Integrated Education (IJIE) published version of the work (e.g., post it to an institutional repository or edit it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) before and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.